Cornelius WCC700 Manuel d'utilisateur télécharger pdf

EIMI Cornelius Inc; 2001

Revision A

620919550

November 30, 2001

IMI CORNELIUS INC.

One Cornelius Place

Anoka. MN 55303-6234

Telephone (800) 238–3600

Facsimile (763) 422–3246

DUAL DF/ED 2XX LID KIT FOR THE FOLLOWING ICE

MAKERS: Cornelius Extreme 522 and Wilshire WCC 700

Dispenser DF/ED 2XX

Kit Number 629087947

Components Qty

1. Cover 620043547 2

2. Lid Assembly (XAC 522 Icemaker) 620046064 1

3. Lid Assembly (WCC 700 Icemaker) 620046060 1

4. Mounting Bracket 22127 4

5. Screw, #8 SM 70217 20

6. RTV 50904 1

7. Label 91957 2

8. Instructions 620919550 1

9. Nut, Nylon 620701902 4

10. Washer, Nylon 620701903 4

11. Washer, Sealing 620701901 4

12. Ice Baffle 620037003 2

13. Gasket Strip 620505802 2

14. Binstat Kit 631500109 1

15. Plate, Top Cover 620044644 1

1. Unpack kit. Refer to Figures 1 & 2 for component detail.

2. Attach the ice baffles (item 12) to the lid assemblies (items 2 & 3) using the gasket strips, washers and acorn

nuts provided (figure 1).

3. Replace the center–mounting bracket supplied with the dual merchandiser kit with the top cover plate sup-

plied with this kit (item 15). Failure to do this will prevent the adapter kit from functioning properly.

4. Set the lid assembly onto the dispenser. Using the slotted holes on the side of the lid as a template, drill four

(4) 9/64” diameter holes at the bottom of the slots (Figure 2).

Note: Use extreme care not to drill into the hopper. Use a drill stop to ensure that the drill bit does not

penetrate deeper than ¼” past the sheet metal. Failure to do so could result in a hole in the hopper, great-

ly reducing the efficiency of both the dispenser and ice maker.

5. Fasten the lid to the dispenser with four (4) #8 sheet metal screws (item 5), two on each side.

6. Seal the ice maker to the top of the dispenser as follows:

A. Run beads of RTV (item 7) around the opening in the lid assembly and the inside of the perimeter of the

ice maker outline so that the ice maker will set on the RTV. Make sure that some RTV is applied inside

the nutserts on the lid assembly.

B. Set the ice maker onto the lid and position it as required.

C. Insert the thumbscrews (item 5) into the lid to attach the icemaker to the lid (Figure 3).

D. Wipe away the excess RTV.

1 2 3 4 5

Résumé du contenu

Page 1

EIMI Cornelius Inc; 2001Revision A620919550November 30, 2001IMI CORNELIUS INC.One Cornelius PlaceAnoka. MN 55303-6234Telephone (800) 238–3600Facsimile

Page 2 - November 30, 2001

EIMI Cornelius Inc; 2001Revision A620919550November 30, 20017. Attach the mounting brackets (item 4) to the to the ice makers and lid assemblies with

Page 3

EIMI Cornelius Inc; 2001Revision A620919550November 30, 20019101113122X4X4X4X2XFIGURE 1. PARTSSECTION W–WSCALE 0.625911131210

Page 4 - SEE VIEW ”X”

EIMI Cornelius Inc; 2001Revision A620919550November 30, 2001FIGURE 2. DISPENSER ASSEMBLYWCC700 ICEMAKER454X16XSEAL ICEMAKER(S) TOITEM 2 AND 3 WITHITEM

Page 5 - FIGURE 3b. OPEN POSITION

EIMI Cornelius Inc; 2001Revision A620919550November 30, 2001FIGURE 3a. CLOSED POSITIONSCALE 0.2501WCC700 ICEMAKERLID ASSEMBLYEXTREME 522 ICEMAKERFIGUR

Commentaires sur ces manuels

Pas de commentaire

Cornelius WCC700 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Kits de voiture Cornelius WCC700. Cornelius WCC700 User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Kits de voiture Cornelius WCC700